Cookie Settings
Dyson websites use cookies. By continuing to use our websites, you accept that cookies may be stored on your device, as outlined in our cookie policy.
Please follow the steps in the video.
After washing the filter, please leave at least 24 hours to dry completely before refitting into the assembly.
Ensure the machine is switched off and unplugged.
Push the red button on the top of the carrying handle to remove the cyclone and clear bin from the machine.
Unclip the front of the carrying handle and remove the filter.
Wash the filter with cold water only.
Squeeze and twist the filter with both hands to make sure the excess water is removed.
Leave the filter to dry for 24 hours.
Once the filter is dry, refit the filter into the top of the cyclone.
Clip the lid down on the cyclone.
Place the clear bin and cyclone back onto the machine ensuring it clicks securely.
Remove the Turbine head and turn the machine on.
Fully remove the floor tool from the machine.
Check the underneath of the floor tool and both inlets for blockages and remove as necessary.
We're glad the problem's been solved.
Please let us know if there's anything else we can help you with.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our team via live chat.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our team via live chat.
Remove the Turbine head and turn the machine on.
Remove the Turbine head from the extension Wand by pressing the release catch. Use a coin to turn the fastener anti-clockwise and remove the Brush bar.
Clean any hair, thread and debris from the Brush bar.
With the Cleaner head removed, check the openings on the tool for blockages and remove if necessary.
Refit the Brush bar and refit the end cap, turning clockwise to lock.
Rebuild and test the machine.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our team via live chat.
Remove the hose, Wand handle and extension tube.
Separate the extension tube from the Wand handle by pressing the release catch on the extension tube.
Check there are no cracks in the handle.
Check the seal on the Wand handle is in place and is not damaged.
Check the extension tube seal is in place and is not damaged.
Check there are no rips or tears.
Ensure the seal is in place and is not damaged.
Remove the bin fully from the machine.
Check both seals on the Main body are in place and not damaged.
Remove the clear bin from the cyclone.
Firmly push the red bin release button.
The bin will slide down, cleaning the shroud as it goes.
The bin base will then open.
Pull the silver catch behind the red bin release button and slide the clear bin off the spine on the cyclone.
Check both seals on the bin are in place and are not damaged.
Check the seal on the cyclone is in place and not damaged.
Insert the spine into the bin runner.
Push upwards until it clicks and then continue pushing until it slides home.
Close the clear bin by pushing the bin base upwards. Ensure that the bin base clicks and the clip is securely in place.
Attach the bin/cyclone to the machine, ensuring it clicks into place.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our team via live chat.
To minimise dust/allergen contact when emptying, encase the clear bin tightly in a plastic bag and empty.
To remove the cyclone and clear bin unit, push the red button on the top of the carrying handle, as shown.
Check the openings of the duct and bin for any blockages and remove as necessary.
To release the dirt, firmly push the red bin release button.
The bin will slide down, cleaning the shroud as it goes.
The bin base will then open.
The bin base will not open if the red button is not pushed down fully.
To remove the clear bin unit, pull the silver catch behind the red bin release button and slide the clear bin off the spine on the cyclone.
Clean the clear bin with cold water only.
Do not use detergents, polishes or air fresheners to clean the clear bin.
Do not put the clear bin in a dishwasher.
Do not immerse the cyclone in water or pour water into the cyclones.
Ensure the clear bin is completely dry before replacing.
Check the cyclone inlet and openings for any blockages and remove as necessary.
To refit the clear bin Insert the spine into the bin runner.
Close the clear bin by pushing the bin base upwards. Ensure that the bin base clicks and the clip is securely in place.
Separate the extension tube from the wand handle by pressing the release catch on the extension tube.
Remove the Wand handle from the hose by pressing the release catch on the hose.
Press the release catch and remove the hose from the appliance.
Check the extension tube, Wand handle and hose for blockages and remove as necessary.
With the bin removed from the front of the machine; take hold of the clear plastic duct on the machine and remove it.
Check the duct and the openings into the machine for any blockages; remove as necessary.
Refit the inspection duct and bin. Retest the machine.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our team via live chat.
Remove any tool from the extension tube.
Fully extend the extension tube by pressing the red button.
Turn the machine on and place your hand over the end of the extension tube.
The Pneumatic floor tool automatically adjusts from hard floors to carpets and vice versa. You don't need to adjust it manually.
The suction control slider can be moved to the minus sign if there is too much suction. If the performance is poor with the suction control moved, it should be put back to the plus sign again.
Fully remove the floor tool from the machine.
Check the underneath of the floor tool and both inlets for blockages and remove as necessary.
Please call us to resolve this problem.
It looks like the Pneumatic musclehead floor tool isn't working. We know how to fix it – we just can’t do it online.
One of our Dyson experts can help you get the parts or assistance you need.
Pneumatic musclehead floor tool
Part no. 968626-02
Replacement pneumatic musclehead floor tool for your Dyson vacuum cleaner.
€72.60
Pneumatic musclehead floor tool
Part no. 968626-02
Replacement pneumatic musclehead floor tool for your Dyson vacuum cleaner.
€72.60
Separate the extension tube from the wand handle by pressing the release catch on the extension tube.
Remove the hose from the machine by pressing the release catches on the hose.
Check the extension tube, Wand handle and hose for blockages and remove as necessary.
Reassemble and test machine.
To remove the cyclone and clear bin unit, push the red button on the top of the carrying handle, as shown.
Check the openings of the duct and bin for any blockages and remove as necessary.
To release the dirt, firmly push the red bin release button.
The bin will slide down, cleaning the shroud as it goes.
The red rod should stop level with the clear bin. If not sliding the bin back up will not be possible.
The bin base will then open.
The bin base will not open if the red button is not pushed down fully.
To remove the clear bin unit, pull the silver catch behind the red bin release button and slide the clear bin off the spine on the cyclone.
Clean the clear bin with cold water only.
Do not use detergents, polishes or air fresheners to clean the clear bin.
Do not put the clear bin in a dishwasher.
Do not immerse the cyclone in water or pour water into the cyclones.
Ensure the clear bin is completely dry before replacing.
Check the cyclone inlet and openings for any blockages and remove as necessary.
Insert the spine into the bin runner.
Close the bin by pushing the bin base upwards. Ensure that the bin base clicks and the clip is securely in place.
Check the inlet to the front of the machine for any blockages and remove as necessary.
Please follow the steps in the video.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our team via live chat.
After washing the filter, please leave at least 24 hours to dry completely before refitting into the assembly.
Ensure the machine is switched off and unplugged.
Push the red button on the top of the carrying handle to remove the cyclone and clear bin from the machine.
Unclip the front of the carrying handle and remove the filter.
Wash the filter with cold water only.
Squeeze and twist the filter with both hands to make sure the excess water is removed.
Leave the filter to dry for 24 hours.
Once the filter is dry, refit the filter into the top of the cyclone.
Clip the lid down on the cyclone.
Place the clear bin and cyclone back onto the machine ensuring it clicks securely.
We need a little more information to help us solve your issue.
Please contact our customer service team via live chat.
Remove the Turbine head from the extension Wand by pressing the release catch.
Use a coin to turn the fastener anti-clockwise and remove the Brush bar.
Clean any hair, thread and debris from the Brush bar.
Check the opening on the Cleaner head for blockages and remove as necessary.
Refit the Brush bar and refit the end cap, turning clockwise to lock.
Rebuild and test the machine.
The Turbine head will work if the suction is strong. This issue can be resolved by carrying out performance checks or washing the filter.
Separate the extension tube from the wand handle by pressing the release catch on the extension tube.
Remove the hose from the machine by pressing the release catches on the hose.
Check the extension tube, Wand handle and hose for blockages and remove as necessary.
Reassemble and test machine.
Separate the extension tube from the wand handle by pressing the release catch on the extension tube.
Remove the hose from the machine by pressing the release catches on the hose.
Check the extension tube, Wand handle and hose for blockages and remove as necessary.
Reassemble and test machine.
Separate the extension tube from the wand handle by pressing the release catch on the extension tube.
Remove the Wand handle from the hose by pressing the release catch on the Wand handle.
Remove the hose from the machine by pressing the release catches on the hose.
Check the extension tube, Wand handle and hose for blockages and remove as necessary.
Reassemble and test machine.
Most Dyson vacuums have a built in safety system that stops the machine if it begins to overheat. This usually happens because the filters need washing or your machine is blocked.
Carry out the performance checks, and if your machine cuts out unplug and leave for at least 2 hours to cool down.
Please follow the steps in the video.
Is the power cord or plug damaged?
Are the other household appliances working?
Does the vacuum work when plugged into another socket?
We need a little more information to help us solve your issue.
Please contact our customer service team via live chat.
Press the rear of the switch to make sure it stays in the on position.
Please note: The switch does not light up.
We need a little more information to help us solve your issue.
Please contact our customer service team via live chat.
We need a little more information to help us solve your issue.
Please contact our customer service team via live chat.
A damp or musty smell is caused when dust in the cyclone has come into contact with water.
It may not be a direct contact with water, for example when vacuuming pet hair that is slightly damp, this moisture will combine with the dust in the cyclone causing the smell.
Additionally the smell may occur if the filter goes back into the machine wet.
Remove the bin from the machine by pressing the red Bin release button located on the handle of the bin and cyclone.
Check the openings of the duct and bin for any blockages and remove as necessary.
Open the bin lid by pressing the red button on top of the cyclone, be careful to do this somewhere to capture any dust securely.
Push the grey button on the side of the cyclone to release the bin from the cyclone assembly.
Use a dry cloth to clean around the cyclone to remove any finer dust or debris.
Check underneath the cyclone for any blockages and remove as necessary.
Reassemble and test machine.
Please follow steps in the video.
After washing the filter, please leave at least 24 hours to dry completely before refitting into the assembly.
Ensure the machine is switched off and unplugged.
Push the red button on the top of the carrying handle to remove the cyclone and clear bin from the machine.
Unclip the front of the carrying handle and remove the filter.
Wash the filter with cold water only.
Squeeze and twist the filter with both hands to make sure the excess water is removed.
Leave the filter to dry for 24 hours.
Once the filter is dry, refit the filter into the top of the cyclone.
Clip the lid down on the cyclone.
Place the clear bin and cyclone back onto the machine ensuring it clicks securely.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our team via live chat.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our team via live chat.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our team via live chat.
You might need a replacement part.
It looks like the Quick-release Combination tool is not working. You can solve this by ordering a new one below.
Quick-release Combination tool
Part no. 967368-01
Two tools in one, for versatile cleaning around the home.
€33.28
Quick-release Combination tool
Part no. 967368-01
Two tools in one, for versatile cleaning around the home.
€33.28
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our team via live chat.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our team via live chat.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our team via live chat.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our team via live chat.
Please call us to resolve this problem.
It looks like the Pneumatic musclehead floor tool isn't working. We know how to fix it – we just can’t do it online.
One of our Dyson experts can help you get the parts or assistance you need.
Pneumatic musclehead floor tool
Part no. 968626-02
Replacement pneumatic musclehead floor tool for your Dyson vacuum cleaner.
€72.60
Pneumatic musclehead floor tool
Part no. 968626-02
Replacement pneumatic musclehead floor tool for your Dyson vacuum cleaner.
€72.60
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our team via live chat.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our team via live chat.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our team via live chat.
The Brush bar on the Turbine head will start spinning as soon as the machine is turned on. You can toggle the Brush bar spin speed by pulling the air release trigger on the Wand handle. There is no need to turn the Brush bar on and off for different floor types.
Remove the Turbine head from the extension Wand by pressing the release catch.
Use a coin to turn the fastener anti-clockwise and remove the Brush bar.
Clean any hair, thread and debris from the Brush bar.
Check the opening on the Cleaner head for blockages and remove as necessary.
Refit the Brush bar and refit the end cap, turning clockwise to lock.
Rebuild and test the machine.
Press the release catch and remove the floor tool.
With the Cleaner head removed, check the openings on the tool for blockages and remove if necessary.
Check the tool for signs of damage.
For use on carpet flooring, the purple seal should be in the 'up' position.
For use on hard flooring, the purple seal should be in the 'down' position.
Check the Brush bar through the window at the front of the Cleaner head.
Check the soleplate to ensure there is no debris or damage to the wheels, and check the wheels are not missing.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our team via live chat.
Adjust the slider on the Cleaner head from MAX to min and retest the machine.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our team via live chat.
The Brush bar on the Turbine head will start spinning as soon as the machine is turned on. You can toggle the Brush bar spin speed by pulling the air release trigger on the Wand handle. There is no need to turn the Brush bar on and off for different floor types.
Remove the Turbine head from the extension Wand by pressing the release catch.
Use a coin to turn the fastener anti-clockwise and remove the Brush bar.
Clean any hair, thread and debris from the Brush bar.
Check the opening on the Cleaner head for blockages and remove as necessary.
Refit the Brush bar and refit the end cap, turning clockwise to lock.
Rebuild and test the machine.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our team via live chat.
Remove any tool from the extension tube.
Fully extend the extension tube by pressing the red button.
Turn the machine on and place your hand over the end of the extension tube.
Attach the hose to the hose inlet on the front of the machine.
Clip the hose to the rear of the Wand handle.
Clip the Wand handle to the extension tube.
Press the release catch on the extension tube to extend, ensuring it 'clicks' into place.
Attach the floor tool to the extension tube.
Insert the tools into the holster and attach to the extension tube.
We're glad the problem's been solved.
Please let us know if there's anything else we can help you with.
The Pneumatic floor tool automatically adjusts from hard floors to carpets and vice versa. You don't need to adjust it manually.
Connect the floor tool to the extension tube, ensuring it clicks into place.
You can adjust the extension tube as you wish by pressing the red catch on the extension tube.
The suction control switch can be moved to the minus sign if there is too much suction. If the performance is poor with the suction control switch open, it should be slid to the plus sign again.
There is no need to turn the Brush bar on and off for different floor types the floor tool has a row of anti-static carbon fibre filaments to remove fine dust from hard floors, and stiff nylon brushes remove ground-in dirt from carpets. There's no need to turn the Brush bar off when moving from one floor type to another.
Connect the Turbine head to the extension tube and ensure the extension tube is fully extended.
To reduce the suction and slow Brush bar rotation, pull the release trigger.
The accessory tools can be attached to the extension tube, Wand handle or hose.
Ensure the click securely into place before use.
Hold the plug when rewinding onto cable reel. Do not allow the plug to whip when rewinding.
To retract the cable, press the button firmly until it clicks and the cable rewinds.
To reduce the suction pull the release trigger.
Store the floor tool by inserting it in the clip at the back of the Main body.
Storing the accessory tools:
Attach the tools to the tool holster.
Clip the tool holster to the extension tube as shown below.
Underneath the machine between the wheels.
Please follow the steps in the video.
Empty as soon as the dirt reaches the level of the MAX mark - do not overfill.
Switch off and unplug before emptying the clear bin.
To remove the cyclone and clear bin unit, push the red button on the top of the carrying handle, as shown.
To release the dirt, firmly push the red bin release button.
The bin will slide down, cleaning the shroud as it goes.
The red rod should stop level with the clear bin. If not sliding the bin back up will not be possible.
The bin base will then open.
The bin base will not open if the red button is not pushed down fully.
Close the clear bin by pushing the bin base upwards until it clicks into place.
Push the bin base clip firmly until it clicks into position to ensure that the base is securely sealed.
Align the base of the bin with the air hose inlet and then click back into place.
You will only be able to remove the bin when the red rod has been pushed down fully so that it is flush with the bin.
In the event that it is necessary to clean the clear bin:
You will only be able to remove the bin when the red rod has been pushed down fully so that it is flush with the bin.
Pull the silver catch behind the red bin release button and slide the clear bin off the spine on the cyclone.
Clean the clear bin with cold water only.
Do not use detergents, polishes or air fresheners to clean the clear bin.
Do not put the clear bin in a dishwasher.
Do not immerse the cyclone in water or pour water into the cyclones.
Ensure the clear bin is completely dry before replacing.
Insert the spine into the bin runner.
Push upwards until it clicks and then continue pushing until it slides home.
Close the clear bin by pushing the bin base upwards. Ensure that the bin base clicks and the clip is securely in place.
Dyson Big Ball Animal 2