Skip navigation
Thanks. We've saved your preferences.
You can update your contact preferences at any time in the Keep in touch section of Your Dyson. If you have a Your Dyson account, you can log in below to manage your contact options.

Dyson Light Ball Multi Floor vacuum

Let's get your machine working.

See all steps

Please select the appropriate option

Clean the bin and cyclone

Press the button at the top of the cyclone handle and remove the bin from the machine.

Press the button again to open the bin base.

Press the button near the rectangular inlet to separate the clear bin from the cyclone.

The clear bin can be wiped with a damp cloth.

Do not use any detergent or polish on any part of the machine.

Check the bin and cyclone for blockages and remove as necessary.

Clear any hair or fibres from the cyclone shroud

Do not use any water on the cyclone.

Once the parts are completely dry, reassemble and test the machine.

Is there anything else we can help with?

We need a little more information to help us solve your issue.

Please call our customer service team on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Please select the appropriate option

Check for blockages

This would suggest there is a blockage somewhere in the machine.

Please follow the next step.

Check inlet suction

Turn off and unplug the machine.

Recline the machine into the vacuuming position.

Lay the machine on its front. There is a red latch on the connection between the ball and Cleaner head. Slide it towards the ball, supporting the machine as you do so.

Pull the Cleaner head away from the machine. Use a constant, firm pressure.

Turn the vacuum over so that the bin is facing upwards. Place your hand over the opening then turn on and test the suction.

Is the suction at the Cleaner head inlet strong or is it weaker than usual?

Check the Cleaner head

Turn off and unplug the machine.

Lay the machine on its front. There is a red latch on the connection between the ball and Cleaner head. Slide it towards the ball, supporting the appliance as you do so.

Pull the Cleaner head away from the appliance. Use a constant, firm pressure.

Beware of sharp objects when clearing obstructions.

There is a silver button on the back of the Cleaner head. Press it down and rotate the end cap to the open position and place it aside. Gently slide the cylindrical Brush bar out from the Cleaner head.

Remove any debris such as hair from the Brush bar.

Slide the Brush bar back into the Cleaner head. Place the end cap back on at a 45° angle and twist upwards.

Lay the machine on its back.

Attach the Cleaner head by sliding it on to the connections on the lower front part of the ball. Ensure the electrical plug on the Cleaner head fits into the twin–block connection on the body of the machine which is directly above the airway.

Push firmly: the Cleaner head will click into place.

Has this resolved the problem?

We need a little more information to help us solve your issue.

Please call our customer service team on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

We're glad the problem's been solved.

Please let us know if there's anything else we can help you with.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Check the duct and internal hose

Turn off and unplug the machine.

Press the release catch on top of the cyclone and remove the bin.

Check the entry duct hatch for obstructions and that the seal is correctly seated.

Pull the internal hose collar down, unclip it and then check for blockages.

Ensure there is no debris or blockages in the changeover valve.

Reassemble and test machine.

Has this resolved the problem?

Check the bin and cyclone

Press the button at the top of the cyclone handle and remove the bin from the machine.

Press the button again to open the bin base.

Press the button near the rectangular inlet to remove the clear bin from the cyclone.

Check the bin and cyclone for blockages and remove as necessary.

Clear any hair or fibres from the cyclone shroud

Do not use any water on the cyclone.

Gently tap the side of the cyclone over a bin - this will remove any fine dust clogged up in the cyclone.

Has clearing the bin and cyclone resolved the problem?

Washing the filters

Please follow the steps in the video.

Has washing the filters resolved the problem?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Remove the pre-filter

Remove the bin and cyclone from the machine and unclip the cyclone top handle.

Pull the filter out from the cyclone.

Wash with cold water only. Do not use detergents.

Remove the post-filter

Turn the central locking dial on the outer cover of the ball counter-clockwise until the cover is released. Lift off the cover.

Turn the filter one-quarter counter-clockwise to release.

Separate the inner foam ring from the outer filter and shell.

The filter should be rinsed and tapped out until the water runs clean, then tapped out again to ensure all excess water is removed.

Dry the filter

Leave to dry completely for 24 hours.

Test the machine

Reassemble and test machine.

Has washing the filters resolved the problem?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Turn off the Brush bar

Plug the machine in and recline into the vacuuming position.

Turn the machine on.

Turn the Brush bar off using the switch next to the power button.

Has the noise stopped?

Clear the Cleaner head

Turn off and unplug the machine.

Lay the appliance on its front. There is a red latch on the connection between the ball and cleaner head. Slide it towards the ball, supporting the appliance as you do so.

Pull the Cleaner head away from the appliance. Use a constant, firm pressure.

Beware of sharp objects when clearing obstructions.

There is a silver button on the back of the Cleaner head. Press it down and rotate the end cap to the open position and place it aside. Gently slide the cylindrical Brush bar out from the Cleaner head.

Remove any debris such as hair from the Brush bar.

Reassemble the machine

Slide the brush bar back into the cleaner head. Place the end cap back on at a 45° angle and twist upwards.

Lay the machine on its back.

Attach the Cleaner head by sliding it on to the connections on the lower front part of the ball. Ensure the electrical plug on the Cleaner head fits into the twin–block connection on the body of the machine which is directly above the airway.

Push firmly: the Cleaner head will click into place.

Has clearing the Cleaner head resolved the problem?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

We need a little more information to help us solve your issue.

Please call our customer service team on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Remove the bin and cyclone

Press the button at the top of the cyclone handle.

Remove the bin and cyclone from the machine.

Turn the machine on, keeping it in the upright position.

Is the whistle still present with the cyclone removed?

Remove the post-filter

Recline the machine and lay it on its back or side.

Turn the centre circle and remove the ball cover.

Separate the inner foam ring from the outer filter and shell.

Turn the machine on.

Is the whistle still present with the post-filter removed?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Refit the filter ensuring it sits flush against the inside of the ball.

Turn the machine on.

Has refitting the post-filter resolved the problem?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Check the seals

Check the seals for signs of wear or damage.

Flex out the seals' outer edges to make sure they sit flush against the corresponding openings.

Please select the appropriate option

Check inlet suction

Turn off and unplug the machine.

Recline the machine into the vacuuming position.

Lay the machine on its front. There is a red latch on the connection between the ball and Cleaner head. Slide it towards the ball, supporting the machine as you do so.

Pull the Cleaner head away from the machine. Use a constant, firm pressure.

Turn the vacuum over so that the bin is facing upwards. Place your hand over the opening then turn on and test the suction.

Is the suction at the Cleaner head inlet strong or is it weaker than usual?

Remove the post-filter

Recline the machine and lay it on its back or side.

Turn the centre circle and remove the ball cover.

Twist the filter and remove from the ball.

Check the housing for any debris and remove as necessary.

Replace post-filter cover and move machine without post-filter in place.

Is the clicking noise still present?

Refit the filter

Place the filter back in the ball.

Ensure that the filter and ball cover are fitted securely.

Test the machine.

Has refitting the post-filter resolved the problem?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Where have you noticed the drop in performance?

Check the Brush bar

Plug in and switch on the machine.

Recline it into the vacuuming position.

Check the Brush bar through the window at the front of the Cleaner head.

Check inlet suction

Turn off and unplug the machine.

Recline the machine into the vacuuming position.

Lay the machine on its front.

There is a red latch on the connection between the ball and Cleaner head. Slide it towards the ball, supporting the machine as you do so.

Pull the Cleaner head away from the appliance. Use a constant, firm pressure.

Turn the vacuum over so that the bin is facing upwards. Place your hand over the opening then turn on and test the suction.

Is the suction at the Cleaner head inlet strong or weaker than usual?

Reset the Brush bar

To reset the Brush bar press the Brush bar control button twice or switch the machine off and back on.

Please note: In normal use, the Brush bar automatically turns off when the machine is upright and automatically turns on when the machine is in the vacuuming position.

Are the bristles now spinning?

Has this resolved the problem?

Check the inlet suction

Turn off and unplug the machine.

Recline the machine into the vacuuming position.

There is a red latch on the connection between the ball and Cleaner head. Slide it towards the ball, supporting the appliance as you do so.

Pull the Cleaner head away from the appliance. Use a constant, firm pressure.

Turn the vacuum over so that the bin is facing upwards. Place your hand over the opening then turn on and test the suction.

Is there strong suction from the inlet?

Clear the Cleaner head

Please follow the steps in the video.

Bristles spinning

To reset the Brush bar press the Brush bar control button twice or switch the machine off and back on.

Please note: In normal use, the Brush bar automatically turns off when the machine is upright and automatically turns on when the machine is in the vacuuming position.

Has this resolved the performance issue?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Clear the Cleaner head

Turn off and unplug the machine.

Lay the appliance on its front. There is a red latch on the connection between the ball and cleaner head. Slide it towards the ball, supporting the appliance as you do so.

Pull the Cleaner head away from the appliance. Use a constant, firm pressure.

Beware of sharp objects when clearing obstructions.

There is a silver button on the back of the Cleaner head. Press it down and rotate the end cap to the open position and place it aside. Gently slide the cylindrical Brush bar out from the Cleaner head.

Remove any debris such as hair from the Brush bar.

Slide the Brush bar back into the Cleaner head. Place the end cap back on at a 45° angle and twist upwards.

Lay the machine on its back.

Attach the Cleaner head by sliding it on to the connections on the lower front part of the ball. Ensure the electrical plug on the Cleaner head fits into the twin–block connection on the body of the machine which is directly above the airway.

Push firmly: the Cleaner head will click into place.

Does the Brush bar spin?

Clear the Cleaner head

Turn off and unplug the machine.

Lay the appliance on its front. There is a red latch on the connection between the ball and cleaner head. Slide it towards the ball, supporting the appliance as you do so.

Pull the Cleaner head away from the appliance. Use a constant, firm pressure.

Beware of sharp objects when clearing obstructions.

There is a silver button on the back of the Cleaner head. Press it down and rotate the end cap to the open position and place it aside. Gently slide the cylindrical Brush bar out from the Cleaner head.

Remove any debris such as hair from the Brush bar.

Slide the Brush bar back into the Cleaner head. Place the end cap back on at a 45° angle and twist upwards.

Lay the machine on its back.

Attach the Cleaner head by sliding it on to the connections on the lower front part of the ball. Ensure the electrical plug on the Cleaner head fits into the twin–block connection on the body of the machine which is directly above the airway.

Push firmly: the Cleaner head will click into place.

Do the brushes now spin continually?

Bristles spinning

To reset the Brush bar press the Brush bar control button twice or switch the machine off and back on.

Please note: In normal use, the Brush bar automatically turns off when the machine is upright and automatically turns on when the machine is in the vacuuming position.

Has this resolved the performance issue?

Check the inlet suction

Turn off and unplug the machine.

Recline the machine into the vacuuming position.

There is a red latch on the connection between the ball and Cleaner head. Slide it towards the ball, supporting the appliance as you do so.

Pull the Cleaner head away from the appliance. Use a constant, firm pressure.

Turn the vacuum over so that the bin is facing upwards. Place your hand over the opening then turn on and test the suction.

Is there strong suction from the inlet?

Reset the Brush bar

To reset the Brush bar press the Brush bar control button twice or switch the machine off and back on.

Please note: In normal use, the Brush bar automatically turns off when the machine is upright and automatically turns on when the machine is in the vacuuming position.

Are the bristles now spinning?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Test the hose suction

To release the Wand, open the Wand cap and pull the Wand up and away from the handle until it clicks into place.

p>Press the button on the hose collar to release the Wand from the hose.

Test the suction from the hose.

Is the suction from the hose strong or weaker than usual?

Check the Cleaner head

Turn off and unplug the machine.

Lay the appliance on its front. There is a red latch on the connection between the ball and Cleaner head. Slide it towards the ball, supporting the appliance as you do so.

Pull the Cleaner head away from the appliance. Use a constant, firm pressure.

Beware of sharp objects when clearing obstructions.

There is a silver button on the back of the Cleaner head. Press it down and rotate the end cap to the open position and place it aside. Gently slide the cylindrical Brush bar out from the Cleaner head.

Remove any debris such as hair from the Brush bar.

Slide the Brush bar back into the Cleaner head. Place the end cap back on at a 45° angle and twist upwards.

Lay the machine on its back.

Attach the Cleaner head by sliding it on to the connections on the lower front part of the ball. Ensure the electrical plug on the Cleaner head fits into the twin–block connection on the body of the machine which is directly above the airway.

Push firmly: the Cleaner head will click into place.

Has this resolved the problem?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Check the hose

Please follow the steps in the video.

Has checking the hose resolved the problem?

Check the bin and cyclone

Press the button at the top of the cyclone handle and remove the bin from the machine.

Press the button again to open the bin base.

Press the button near the rectangular inlet to remove the clear bin from the cyclone.

Check the bin and cyclone for blockages and remove as necessary.

Clear any hair or fibres from the cyclone shroud

Do not use any water on the cyclone.

Gently tap the side of the cyclone over a bin (this will remove any fine dust clogged up in the cyclone).

Has clearing the bin and cyclone resolved the problem?

Washing the filters

Please follow the steps in the video.

Has washing the filters resolved the problem?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Remove the pre-filter

Remove the bin and cyclone from the machine and unclip the cyclone top handle.

Pull the filter out from the cyclone.

Wash with cold water only. Do not use detergents.

Remove the post-filter

Turn the central locking dial on the outer cover of the ball counter-clockwise until the cover is released. Lift off the cover.

Turn the filter one-quarter counter-clockwise to release.

Separate the inner foam ring from the outer filter and shell.

The filter should be rinsed and tapped out until the water runs clean, then tapped out again to ensure all excess water is removed.

Dry filters

Leave to dry completely for 24 hours.

Test the machine

Reassemble and test the machine.

Has washing the filters resolved the problem?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Check the hose

Press the button at the top of the cyclone handle and remove the bin from the machine.

To remove the hose press the release catch firmly and pull on the hose.

Check the hose for any holes or tears and remove any blockages.

Reassemble and test the machine.

Has checking the hose resolved the problem?

Check the bin and cyclone

Press the button at the top of the cyclone handle and remove the bin from the machine.

Press the button again to open the bin base.

Press the button near the rectangular inlet to remove the clear bin from the cyclone.

Check the bin and cyclone for blockages and remove as necessary.

Clear any hair or fibres from the cyclone shroud

Do not use any water on the cyclone.

Gently tap the side of the cyclone over a bin (this will remove any fine dust clogged up in the cyclone).

Has clearing the bin and cyclone resolved the problem?

Washing the filters

Please follow the steps in the video.

Has washing the filters resolved the problem?

Check the duct and internal hose

Turn off and unplug the machine.

Press the release catch on top of the cyclone and remove the bin.

Check the entry duct hatch for obstructions and that the seal is correctly seated.

Pull the red internal hose collar down, unclip it and then check for blockages.

Reassemble and test the machine.

Has clearing the duct and internal hose resolved the problem?

When did the machine last have power?

Thermal cut out

Most Dyson vacuums have a built in safety system that stops the machine if it begins to overheat. This usually happens because the filters need washing or your machine is blocked.

Carry out the performance checks, and if your machine cuts out unplug and leave for at least 2 hours to cool down.

Check electrical supply

Is the power cord or plug damaged?

Are the other household appliances working?

Does the vacuum work when plugged into another socket?

Change the (13 amp) fuse.

Has checking the electrics resolved the problem?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Reset the Brush bar

To reset the Brush bar press the Brush bar control button twice or switch the machine off and back on.

Please note: In normal use, the Brush bar automatically turns off when the machine is upright and automatically turns on when the machine is in the vacuuming position.

Please select the appropriate option

Check the Brush bar

Plug in and switch on the machine.

Recline it into the vacuuming position.

Check the Brush bar through the window at the front of the Cleaner head.

Are the bristles now spinning?

Clear the Cleaner head

Turn off and unplug the machine.

Lay the appliance on its front. There is a red latch on the connection between the ball and cleaner head. Slide it towards the ball, supporting the appliance as you do so.

Pull the Cleaner head away from the appliance. Use a constant, firm pressure.

Beware of sharp objects when clearing obstructions.

There is a silver button on the back of the Cleaner head. Press it down and rotate the end cap to the open position and place it aside. Gently slide the cylindrical Brush bar out from the Cleaner head.

Remove any debris such as hair from the Brush bar.

Slide the Brush bar back into the Cleaner head. Place the end cap back on at a 45° angle and twist upwards.

Lay the machine on its back.

Attach the Cleaner head by sliding it on to the connections on the lower front part of the ball. Ensure the electrical plug on the Cleaner head fits into the twin–block connection on the body of the machine which is directly above the airway.

Push firmly: the Cleaner head will click into place.

Do the brushes spin now?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

The switch does not light up.

Press the switch

Press the rear of the switch to make sure it stays in the on position.

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Check the bin and cyclone

Press the button at the top of the cyclone handle and remove the bin from the machine.

Press the button again to open the bin base.

Press the button near the rectangular inlet to separate the clear bin from the cyclone.

The clear bin can be wiped with a damp cloth.

Do not use any detergent or polish on any part of the machine.

Check the bin and cyclone for blockages and remove as necessary.

Clear any hair or fibres from the cyclone shroud

Do not use any water on the cyclone.

Once the parts are completely dry, reassemble and test the machine.

Has cleaning the bin and cyclone resolved the problem?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Has the ball shell come off the filter side or non-filter side?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Has the nut come out of the centre of the ball shell?

We need a little more information to help us solve your issue.

Please call our customer service team on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Release the catch by hand

Pull the clear plastic catch on the base away from the bin.

Open the bin base and tip away the contents.

Press the bin release button on the cyclone handle.

Does the rod on the side of the bin slide up and down freely?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Reset the Brush bar

To reset the Brush bar press the Brush bar control button twice or switch the machine off and back on.

Please note: In normal use, the Brush bar automatically turns off when the machine is upright and automatically turns on when the machine is in the vacuuming position.

Please select the appropriate option

Check the Brush bar

Plug in and switch on the machine.

Recline it into the vacuuming position.

Check the Brush bar through the window at the front of the Cleaner head.

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Clear the Cleaner head

Turn off and unplug the machine.

Lay the appliance on its front. There is a red latch on the connection between the ball and cleaner head. Slide it towards the ball, supporting the appliance as you do so.

Pull the Cleaner head away from the appliance. Use a constant, firm pressure.

Beware of sharp objects when clearing obstructions.

There is a silver button on the back of the Cleaner head. Press it down and rotate the end cap to the open position and place it aside. Gently slide the cylindrical Brush bar out from the Cleaner head.

Remove any debris such as hair from the Brush bar.

Slide the Brush bar back into the Cleaner head. Place the end cap back on at a 45° angle and twist upwards.

Lay the machine on its back.

Attach the Cleaner head by sliding it on to the connections on the lower front part of the ball. Ensure the electrical plug on the Cleaner head fits into the twin–block connection on the body of the machine which is directly above the airway.

Push firmly: the Cleaner head will click into place.

Do the brushes spin now?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Bristles spinning

To reset the Brush bar press the Brush bar control button twice or switch the machine off and back on.

Please note: In normal use, the Brush bar automatically turns off when the machine is upright and automatically turns on when the machine is in the vacuuming position.

Has this resolved the performance issue?

Check the inlet suction

Turn off and unplug the machine.

Recline the machine into the vacuuming position.

There is a red latch on the connection between the ball and Cleaner head. Slide it towards the ball, supporting the appliance as you do so.

Pull the Cleaner head away from the appliance. Use a constant, firm pressure.

Turn the vacuum over so that the bin is facing upwards. Place your hand over the opening then turn on and test the suction.

Is there strong suction from the inlet?

Clear the Cleaner head

Turn off and unplug the machine.

Lay the appliance on its front. There is a red latch on the connection between the ball and cleaner head. Slide it towards the ball, supporting the appliance as you do so.

Pull the Cleaner head away from the appliance. Use a constant, firm pressure.

Beware of sharp objects when clearing obstructions.

There is a silver button on the back of the Cleaner head. Press it down and rotate the end cap to the open position and place it aside. Gently slide the cylindrical Brush bar out from the Cleaner head.

Remove any debris such as hair from the Brush bar.

Slide the brush bar back into the cleaner head. Place the end cap back on at a 45° angle and twist upwards.

Lay the machine on its back.

Attach the Cleaner head by sliding it on to the connections on the lower front part of the ball. Ensure the electrical plug on the Cleaner head fits into the twin–block connection on the body of the machine which is directly above the airway.

Push firmly: the Cleaner head will click into place.

Do the brushes now spin continually?

Check which surface the machine is on.

Is the machine on deep pile carpet?

Check that that suction control slider has the appropriate setting selected.

Has checking the suction control slider resolved the problem?

When did the machine last have power?

Check the duct and internal hose

Turn off and unplug the machine.

Press the release catch on top of the cyclone and remove the bin.

Check the entry duct hatch for obstructions and that the seal is correctly seated.

Pull the internal hose collar down, unclip it and then check for blockages.

Has clearing the duct and internal hose resolved the problem?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Check the duct and internal hose

Turn off and unplug the machine.

Press the release catch on top of the cyclone and remove the bin.

Check the entry duct hatch for obstructions and that the seal is correctly seated.

Replace the bin onto the machine.

Recline the machine into the vacuuming position. Lay the machine on its front.

Pull the internal hose collar down, unclip it and then check for blockages.

Ensure there is no debris or blockages in the changeover valve.

Has checking the duct and internal hose resolved the problem?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Clear the Cleaner head

Turn off and unplug the machine.

Lay the appliance on its front. There is a red latch on the connection between the ball and cleaner head. Slide it towards the ball, supporting the appliance as you do so.

Pull the Cleaner head away from the appliance. Use a constant, firm pressure.

Beware of sharp objects when clearing obstructions.

There is a silver button on the back of the Cleaner head. Press it down and rotate the end cap to the open position and place it aside. Gently slide the cylindrical Brush bar out from the Cleaner head.

Remove any debris such as hair from the brush bar.

Slide the brush bar back into the cleaner head. Place the end cap back on at a 45° angle and twist upwards.

Lay the machine on its back.

Attach the Cleaner head by sliding it on to the connections on the lower front part of the ball. Ensure the electrical plug on the Cleaner head fits into the twin–block connection on the body of the machine which is directly above the airway.

Push firmly: the Cleaner head will click into place.

Please select the appropriate option

Check the duct and internal hose

Turn off and unplug the machine.

Press the release catch on top of the cyclone and remove the bin.

Check the entry duct hatch for obstructions and that the seal is correctly seated.

Pull the internal hose collar down, unclip it and then check for blockages.

Has clearing the Cleaner head resolved the problem?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Replacement part required

This issue can be resolved by ordering a replacement Cleaner head.

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Assembly instructions

Attach the Cleaner head.

Ensure that the connection pins underneath the Cleaner head are located correctly.

Locate the C-clip into place and fit the Cleaner head to the inlet at the base of the machine.

How to attach the accessories

Lower the Wand handle onto the machine ensuring it clicks.

Slide the Wand into the hose and fit to the back of the machine until it 'clicks' into position.

Store the tools.

Remove the cyclone and bin.

Slide the tool holder onto the side of the duct as shown.

Attach the combination tool to the tool holder on the side of the machine.

Attach the stair tool to the tool holder on the side of the machine.

Is there anything else we can help with?

How to use the Brush bar

Note: The Brush bar will automatically switch on when the machine is reclined into the vacuuming position.

Press the brush control button next to the On/Off switch to stop the brushes for use on delicate rugs, loop pile carpets and hard floors.

Press the button again to restart the Brush bar for vacuuming carpets.

Is there anything else we can help you with?

Carrying your Dyson machine

Lift the machine only by the carry handle on the cyclone top.

For your safety, do not press the cyclone release when carrying your machine.

Is there anything else we can help you with?

How to start vacuuming

Plug the machine in.

Pull handle back and recline machine into vacuuming position ensuring the stabilising wheels are facing up towards the back of the machine.

Press the ON/OFF switch.

Small movements of the wrist will create a zig zag motion in the Cleaner head allowing easier cleaning around furniture.

Extend the wand until it clicks.

Press the wand release button and lift the wand out of the hose.

Lift the wand handle cap and push on to the hose until it clicks into place.

Push the combination tool on to the end of the wand handle.

Alternatively, click the combination tool directly to the hose.

Is there anything else we can help you with?

User guide

Please open the PDF for the user guide.

Is there anything else we can help you with?

Washing the filters

Please follow the steps in the video.

Is there anything else we can help you with?

Remove the pre-filter

Remove the bin and cyclone from the machine and unclip the cyclone top handle.

Pull the filter out from the cyclone.

Remove the post-filter

Turn the central locking dial on the outer cover of the ball counter-clockwise until the cover is released. Lift off the cover.

Turn the filter one-quarter counter-clockwise to release.

Separate the inner foam ring from the outer filter and shell.

The filter should be rinsed and tapped out until the water runs clean, then tapped out again to ensure all excess water is removed.

Dry filters

Leave to dry completely for 24 hours.

Test the machine

Reassemble and test the machine.

Is there anything else we can help you with?

Empty the bin

Press the button at the top of the handle and remove the bin from the machine.

Press the button again to open the bin base and release the dust.

This can be done directly into a Bin, or into a bag wrapped around the cyclone.

Is there anything else we can help you with?