Skip navigation
Thanks. We've saved your preferences.
You can update your contact preferences at any time in the Keep in touch section of Your Dyson. If you have a Your Dyson account, you can log in below to manage your contact options.

Dyson V6 Mattress vacuum

Let's get your machine working.

See all steps

Please select the appropriate option

How to charge the battery

The machine can be charged on a dock (if purchased separately) or by plugging the charger directly to the machine.

The light on the charger will show when the machine is being charged and will go out when charging is complete.

The battery should be fully charged after 3.5 hours.

Is there anything else we can help with?

Please select the appropriate option

Remove the bin and turn on the machine

Press the bin base release button to empty bin, leave bin base open.

Press the release button again to remove the bin from the cyclone.

Is the noise still present with the bin removed?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Check the motor's sound

Refit the bin.

Remove all tools and accessories from the machine.

Put the machine in MAX power mode (the light on the MAX power button will illuminate when the trigger is pressed).

Pull and hold the trigger for 10 seconds.

Does the machine pulsate and cut out without any tools?

Clear the floor tool

Undo one fastener to remove the Brush bar.

Remove Brush bar and clear away any hair or fibres. Check the opening for any blockages and remove as necessary.

Refit the Brush bar and lock the fastener.

Reassemble and test machine.

Has this resolved the problem?

We're glad the problem's been solved.

Please let us know if there's anything else we can help you with.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Check the bin inlet

With the bin removed, check the bin inlet flap for blockages and remove as necessary.

Ensure that it moves freely, fluff or fibres jamming the hinge can cause the flap to close resulting in low suction and pulsating noise.

Close the bin base hold the bin so that the inlet is pointing to the floor and shake the bin.

Does the bin rattle?

Check the cyclone

Clean shroud using the brush part of the combination tool.

Clear the centre of the cyclone of any dirt or debris.

Check that the seals are not missing or damaged:

FDC seal between the cyclone and the bin base.

Seal between the cyclone and the top of the bin.

Seal around the bin base.

Reassemble and test machine.

Has checking the cyclone and seals resolved the problem?

Checking the Wand

Remove the Wand from the bin inlet.

Check both ends of the Wand for blockages and remove as necessary.

Reassemble and test machine.

Has checking the Wand resolved the problem?

The video may show a different variant although the process remains the same.

Wash the filter

Please follow the steps in the video.

Has washing the filter resolved the problem?

Soak the filter in cold water for 2 - 3 minutes and gently massage the filter to release built up dust. Repeat this process until the water remains clear.

Removing the filter

Ensure the machine is disconnected from the charger before removing the filter. Be careful not to pull the 'ON' trigger.

To remove the filter, lift it out of the top of the machine.

Note: Your machine has one washable filter, located as shown.

Washing the filter

Prior to washing the filter, tap the filter on a hard surface to remove any debris inside.

Wash the filter with cold water only.

Run water over the outside of the filter until the water runs clear.

Squeeze and twist with both hands to make sure the excess water is removed.

Note: The filter may require more frequent washing if vacuuming fine dust or if used mainly in ‘Powerful suction’ mode.

Filter drying

Lay the filter on its side to dry. Leave to dry completely for a minimum of 24 hours.

Do not put the filter in a dishwasher, washing machine, tumble dryer, oven, microwave or near a naked flame.

Replacing the filter

To refit, place the dry filter back into the top of the appliance. Make sure it is seated properly.

Has washing the filter resolved the problem?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

We need a little more information to help us solve your issue.

Please call our customer service team on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Clear the bin inlet flap

This indicates that the bin entry inlet is jammed.

Re-check the flap and push it open by hand a few times until it is free.

Can the flap be pushed open by hand?

Has this resolved the problem?

Check the cyclone

Clean shroud using brush part of combination tool.

Clear the centre of the cyclone of any dirt or debris.

Check that the seals are not missing or damaged:

FDC seal between the cyclone and the bin base.

Seal between the cyclone and the top of the bin.

Seal around the bin base.

Reassemble and test machine.

Has checking the cyclone and seals solved the problem?

Please call us to resolve this problem.

It looks like the Clear bin isn't working. We know how to fix it – we just can’t do it online.

One of our Dyson experts can help you get the parts or assistance you need.

Clear bin

Part no. 965660-03

Replacement clear bin for your Dyson vacuum cleaner.

€24.99

Clear bin

Clear bin

Part no. 965660-03

Replacement clear bin for your Dyson vacuum cleaner.

€24.99

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Clear the floor tool

With the floor tool removed from the machine, turn over and undo the fastener.

Rotate the end cap to unlock and remove.

Remove the Brush bar and clear away any hair or debris.

Check the openings for any blockages and remove as necessary. Replace the Brush bar.

Use a coin to lock the fastener.

Reassemble and test the machine.

Has this resolved the problem?

Clean the floor tool

Undo one fastener to remove the brushbar.

Remove brushbar and clear away any hair or fibres. Check the opening for any blockages and remove as necessary.

Refit the Brush bar and lock the fastener.

Reassemble and test the machine.

Has this resolved the problem?

Clear the Mini motorised head

With the tool removed from the machine, remove Brush bar and clear away any hair or fibres.

Check the opening for blockages and remove as necessary.

Refit the brushbar ensuring that no bristles get stuck in either end.

Has this resolved the problem?

Clear Hard floor tool

Check through both openings of the head for blockages and remove as necessary.

Reassemble and retest the machine.

Has checking the floor tool resolved the problem?

Remove the bin and turn on the machine

Press the bin base release button to empty Bin and leave the bin base open.

Gently tap the side of the cyclone over a bin - this will remove any fine dust clogged up in the cyclone.

Gently tap the side of the cyclone over a bin (This will remove any fine dust clogged up in the cyclone)

Clean shroud using brush part of combination tool.

Press and hold the trigger for 10 seconds.

Does the machine pulsate with the bin removed?

Remove the pre-filter

Pull the filter out from the cyclone.

Press and hold the trigger for 10 seconds.

Does the machine pulsate with the filter removed?

Please call us to resolve this problem.

It looks like the Main body and screws isn't working. We know how to fix it – we just can’t do it online.

One of our Dyson experts can help you get the parts or assistance you need.

Main body and screws

Part no. 967041-05

Replacement main body for your Dyson vacuum cleaner.

€94.99

Main body and screws

Main body and screws

Part no. 967041-05

Replacement main body for your Dyson vacuum cleaner.

€94.99

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Check the cyclone

If the machine still pulsates with the clear bin and filter removed, the cyclone may be blocked.

Check inside the cyclone for blockages, gently tapping it on the side of a dustbin to remove any debris.

Retest the machine.

Has this resolved the problem?

Check the motor's sound

Remove all tools and accessories from the machine.

Put the machine in MAX power mode (the light on the MAX power button will illuminate when the trigger is pressed).

Pull and hold the trigger for 10 seconds.

Does the machine pulsate and cut out without any tools?

The floor tool in the image may differ to the tool that you have, however the process remains the same..

Test the floor tool

Attach the main floor tool directly onto the bin inlet.

Press and hold trigger for 10 seconds.

Does the machine pulsate and cut out with the floor tool attached?

Which floor tool are you using?

Select the correct floor tool you are using on your machine.

Clear the floor tool

Undo one fastener to remove the Brush bar.

Remove Brush bar and clear away any hair or fibres. Check the opening for any blockages and remove as necessary.

Refit the Brush bar and lock the fastener.

Reassemble and test the machine.

Has checking the floor tool resolved the problem?

Clean the floor tool

Undo one fastener to remove the brushbar.

Remove brushbar and clear away any hair or fibres. Check the opening for any blockages and remove as necessary.

Refit the Brush bar and lock the fastener.

Reassemble and test the machine.

Has clearing the floor tool resolved the problem?

Check the Mini motorised head

Put the mini motorised head on the machine.

Press and hold the trigger for 10 seconds.

Does the machine pulsate and cut out with the Mini motorised head?

Clear the mini motorised head

With the tool removed from the machine, remove Brush bar and clear away any hair of fibre.

Check the opening for blockages and remove as necessary.

Refit the Brush bar ensuring that no bristles get stuck in either end.

Reassemble and test the machine.

Has clearing the Mini motorised head resolved the problem?

Remove the bin and turn on the machine.

Press the bin base release button to empty bin, leave bin base open.

Press the release button again to remove the bin from the cyclone.

Is the noise still present with the bin removed?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Check the motor's sound

Remove all tools and accessories from the machine.

Put the machine in max power mode (the light on the max power button will illuminate when the trigger is pressed).

Pull and hold the trigger for 10 seconds.

Does the machine pulsate and cut out without any tools?

Check the Mini motorised head

Put the mini motorised head on the machine.

Press and hold trigger for 10 seconds.

Does the machine pulsate and cut out with the Mini Motorised head?

Check the sound

Remove all tools and accessories from the machine.

Put the machine in max power mode (the light on the max power button will illuminate when the trigger is pressed).

Pull and hold the trigger for 10 seconds.

Does the machine pulsate and cut out without any tools?

If the machine is being charged in the docking station, please remove the charging cable from the dock and plug it directly into the machine.

If the machine still doesn't charge, please inspect the cable for damage.

Please select the appropriate option

You might need a replacement part.

It looks like the Charger is not working. You can solve this by ordering a new one below.

Charger

Part no. 967813-01

Plugs into a standard three-pin wall socket.

€51.66

Charger

Charger

Part no. 967813-01

Plugs into a standard three-pin wall socket.

€51.66

€51.66

€51.66

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Does the machine currently have power?

Check the motor's sound

Remove all tools and accessories from the machine.

Put the machine in max power mode (the light on the max power button will illuminate when the trigger is pressed).

Pull and hold the trigger for 10 seconds.

Does the machine pulsate and then cut out without any tools?

Check MAX power LED

Press and hold the power trigger.

If the MAX button flashes 5 or less times please order a new Main body.

If the MAX button flashes 7/8 times - the machine is too hot / cold.

Advise the customer to leave the machine in room temperature for 3.5hrs and then to re test the machine.

If the MAX button flashes 10 or more, there will be a blockage somewhere in the machine.

Is there a blue light on the MAX power light when the machine cuts out?

Check the lights on the battery

If the machine has no light on the 'Max' button, check the lights on the battery.

Hold the trigger

Hold in the trigger and count the number of times the light flashes.

How many times did the light flash?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Please call us to resolve this problem.

It looks like the Power pack and screws isn't working. We know how to fix it – we just can’t do it online.

One of our Dyson experts can help you get the parts or assistance you need.

Power pack and screws

Part no. 965874-16

Replacement power pack and screws for your Dyson vacuum cleaner.

€74.99

Power pack and screws

Power pack and screws

Part no. 965874-16

Replacement power pack and screws for your Dyson vacuum cleaner.

€74.99

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Check MAX button

If the machine has no power and you have a blue light on the battery, please check the 'Max' button light and count the flashes for the following:

The flashes may appear quickly - so it will be best to check twice.

If the MAX button flashes 7/8 times - the machine is too hot / cold.

If the MAX button flashes 10 or more, there will be a blockage somewhere in the machine.

Please select the appropriate option

Remove the bin and turn on the machine

Press the bin release button to empty the bin.

With the bin base open, press the button again to remove the bin from the cyclone.

Now press the trigger on the Main body.

Has this resolved the problem?

Removing the filter

Ensure the machine is disconnected from the charger before removing the filter. Be careful not to pull the 'ON' trigger.

To remove the filter, lift it out of the top of the machine.

Note: Your machine has one washable filter, located as shown.

Washing the filter

Wash the filter with cold water only.

Run water over the outside of the filter until the water runs clear.

Squeeze and twist the pre-filter with both hands to make sure the excess water is removed.

Note: The filter may require more frequent washing if vacuuming fine dust or if used mainly in ‘Powerful suction’ mode.

Filter drying

Lay the filter on its side to dry. Leave to dry completely for a minimum of 24 hours.

Do not put the filter in a dishwasher, washing machine, tumble dryer, oven, microwave or near a naked flame.

Replacing the filter

To refit, place the dry filter back into the top of the appliance. Make sure it is seated properly.

Has this resolved the problem?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

We need a little more information to help us solve your issue.

Please call our customer service team on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Charge and check the light

Put the machine on charge and check the light.

What does the light show when the machine is plugged into the charger?

Is the machine being charged in the dock?

Check the connection

Ensure the charger is plugged into the socket and the charger pin is fully pushed into the machine.

What does the light on the battery show?

Charge the machine

This suggests that the battery was running low but is now charging normally.

Please charge battery for 3.5 hours before contacting customer services.

Has this resolved the problem?

We need a little more information to help us solve your issue.

Please call our customer service team on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Test the connection

Wiggle charger cable where it enters the machine.

Does the light show at all, even temporarily?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

We need a little more information to help us solve your issue.

Please call our customer service team on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Return to working temperature

This indicates that the machine is outside of its normal operating temperature (5oc - 35oc).

Please place the machine in an area that stays within this temperature range and leave it to charge there for 3.5 hours.

Has this resolved the problem?

Check the connection

The charger cable may be out of position in the dock.

Remove the charger by pushing charger pin firmly towards the back of the dock.

Once removed, refit by pushing the end of the charger (as you would put a pen into its lid) until it clicks.

Put the machine back on charge.

What does the light on the battery show while the machine is in the dock?

Charge directly into machine

Remove charger cable from the dock and plug directly into the machine.

What does the light show when the machine is plugged into the charger?

Please call us to resolve this problem.

It looks like the Power pack and screws isn't working. We know how to fix it – we just can’t do it online.

One of our Dyson experts can help you get the parts or assistance you need.

Power pack and screws

Part no. 965874-16

Replacement power pack and screws for your Dyson vacuum cleaner.

€74.99

Power pack and screws

Power pack and screws

Part no. 965874-16

Replacement power pack and screws for your Dyson vacuum cleaner.

€74.99

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Retest

Remove the machine from charger.

Pull and hold the trigger while watching the light on the battery.

Is there a red flashing light on the battery?

Try a different plug socket

Plug the machine back in using a different plug socket.

What does the light show in the new plug socket?

Red flashing light

Hold in the trigger and count the number of times the light flashes.

How many times did the light flash?

Hold the trigger

Pull and hold the trigger for 10 seconds.

Reset

Press the button for 3 seconds and release.

Repeat this 5 times.

Is there still an amber light?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Charge the machine

Put the machine on charge for 3.5 hours and test it again.

Please select the appropriate option

Please call us to resolve this problem.

It looks like the Power pack and screws isn't working. We know how to fix it – we just can’t do it online.

One of our Dyson experts can help you get the parts or assistance you need.

Power pack and screws

Part no. 965874-16

Replacement power pack and screws for your Dyson vacuum cleaner.

€74.99

Power pack and screws

Power pack and screws

Part no. 965874-16

Replacement power pack and screws for your Dyson vacuum cleaner.

€74.99

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

MAX power

Check the Max Power light.

Does the light on the MAX power button flash when the trigger is held?

Count the flashes

Hold in the trigger and count how many times the MAX Power button's light flashes.

How many times did the light flash?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Return to working temperature

This indicates that the machine is outside of its normal operating temperature (5oc - 35oc).

7 flashes = Too cold

8 flashes = Too hot

Please place the machine in an area that stays within this temperature range and leave it to charge there for 3.5 hours.

Has this resolved the issue?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Check for blockages

This suggests that the machine is blocked.

Please charge the machine for 3.5 hours so that is has power before carrying out the performance checks.

Please select the appropriate option

Check the sound

Remove all tools and accessories from the machine.

Put the machine in MAX power mode (the light on the MAX power button will illuminate when the trigger is pressed).

Pull and hold the trigger for 10 seconds.

Does the machine pulsate and cut out without any tools?

Test the battery

Cyclone does not need to be removed for this check.

With the bin removed, undo the phillips head screw at the back of the handle.

Undo the Phillips screw in the front of the Main body.

Pull the battery down, out of the Main body.

Press the button on the battery and watch the light on its side.

What does the light on the battery show when it's detached from the machine?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Press and hold the button for 10 seconds.

We need a little more information to help us solve your issue.

Please call our customer service team on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Clear the mini motorised head

With the tool removed from the machine, remove brushbar and clear away any hair or fibres.

Check the opening for blockages and remove as necessary.

Refit the brushbar ensuring that no bristles get stuck in either end.

Does the Brush bar spin without any contact?

Please call us to resolve this problem.

It looks like the Mini motorised tool isn't working. We know how to fix it – we just can’t do it online.

One of our Dyson experts can help you get the parts or assistance you need.

Mini motorised tool

Part no. 962748-07

Tackles hair and ground-in dirt in confined spaces.

€54.99

Mini motorised tool

Mini motorised tool

Part no. 962748-07

Tackles hair and ground-in dirt in confined spaces.

€54.99

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Test the Mini motorised head

Test the Mini motorised head on a surface where it has previously stalled.

Does the Brush bar spin while in contact with this surface?

Is this surface a long pile carpet or rug?

Short pile carpet

Test the tool on a low pile carpet.

Does the Brush bar spin whilst in contact with the low pile carpet?

The issue appears to be resolved

The Brush bar may stall on long piled carpets and rugs, this is normal and helps prevent damage to the machine or surface.

Using the machine in standard (not max) power mode will help avoid this, although it may not be possible to use the motorised head on very long pile.

Is there anything else we can help with?

We're glad the problem's been solved.

Please let us know if there's anything else we can help you with.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Check the electrical contacts

Press the red release catch to open the bin base.

Press the red catch again to release the cyclone top from the bin.

Once the bin is removed, clean the bin electrical contacts and the Main body electrical contacts.

NB: Please ensure the bin base is open when refitting the bin otherwise the contacts may not align correctly causing the Brush bar not to spin.

Has checking the electrical contacts resolved the problem?

Is this surface a long pile carpet or rug?

Try the tool on a low pile carpet.

Does the Brush bar spin while in contact with the short-pile carpet?

We need a little more information to help us solve your issue.

Please call our customer service team on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Clear the floor tool

Undo one fastener to remove the brushbar.

Remove brushbar and clear away any hair or fibres. Check the opening for any blockages and remove as necessary.

Refit the brushbar and lock the fastener.

Reassemble and test the machine.

Has checking the floor tool resolved the problem?

Test the Wand

Remove the tool and wand from the machine.

Put the tool directly onto the machine and test without putting the tool in contact with any surface.

Does the Brush bar spin when the head is attached to the bin inlet?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Test the floor tool

Test the floor tool on a surface where it has previously stalled.

Does the Brush bar spin while in contact with the floor?

Is this surface a long pile carpet or rug?

Clean the floor tool

Undo one fastener to remove the brushbar.

Remove brushbar and clear away any hair or fibres. Check the opening for any blockages and remove as necessary.

Refit the brushbar and lock the fastener.

Reassemble and test machine.

Has checking the floor tool resolved the problem?

Clear the floor tool

With the floor tool removed from the machine, turn over and undo the fastener.

Rotate the end cap to unlock and remove.

Remove the brushbar and clear away any hair or debris.

Check the openings for any blockages and remove as necessary. Replace the Brush bar.

Use a coin to lock the fastener.

Reassemble and test the machine.

Has checking the floor tool resolved the problem?

Check the status lights

Ensure the machine is fully assembled, and pull the trigger.

Check the light at the base of the handle (not the Max Power indicator).

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Has any part of the machine been washed?

Only the filter can be washed, the bin can be cleaned with a damp cloth only, and both must be completely dry before being refitted to the machine.

Were all the washed parts completely dry before the machine was used?

Under normal use, any unpleasant smell can only be caused by something the machine has picked up.

Check the motor's sound

Remove all tools and accessories from the machine.

Put the machine in max power mode (the light on the max power button will illuminate when the trigger is pressed).

Pull and hold the trigger for 10 seconds.

Does the machine pulsate and cut out without any tools?

How to clean the bin and cyclone

Remove the bin

Push the red button by the clear bin to open the bin base.

Press a second time to release the clear bin from the Main body of the appliance.

Remove the clear bin carefully.

Clean the bin

Clean the bin with a damp cloth only.

Do not use detergents, polishes or air fresheners to clean the bin.

Do not put the bin in a dishwasher.

Clean the cyclone shroud

Clean the cyclone shroud with the brush on the combination tool to remove lint and dust.

Do not immerse the whole cyclone unit in water or pour water into the cyclones.

Refit the bin

Ensure the clear bin is completely dry before replacing.

To replace the clear bin, push the clear bin up and in to the Main body of the appliance. It will click into place.

Close the clear bin base so it clicks into place and is secure.

Has cleaning the bin and cyclone resolved the problem?

The video may show a different variant although the process remains the same.

Wash the filter

Please follow the steps in the video.

Has washing the filters resolved the problem?

Machine pick up

Under normal use, any unpleasant smell can only be caused by something the machine has picked up.

We would advise you to carry out the blockage checks.

Ensure the appliance is disconnected from the charger before removing the filter. Be careful not to pull the ‘ON ’ trigger.

Removing the filter

To remove the filter, lift it out of the top of the appliance.

Note: Your appliance has one washable filter, located as shown.

Washing the filter

Wash the filter with cold water only.

Run water over the outside of the filter until the water runs clear.

Squeeze and twist the pre-filter with both hands to make sure the excess water is removed.

Note: The filter may require more frequent washing if vacuuming fine dust or if used mainly in ‘Powerful suction’ mode.

Filter drying

Lay the filter on its side to dry. Leave to dry completely for a minimum of 24 hours.

Do not put the filter in a dishwasher, washing machine, tumble dryer, oven, microwave or near a naked flame.

Replacing the filter

To refit, place the dry filter back into the top of the appliance. Make sure it is seated properly.

Has washing the filters resolved the problem?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

How to clean the clear bin and cyclone

Remove the bin

Push the red button by the clear bin to open the bin base.

Press a second time to release the clear bin from the main body of the appliance.

Remove the clear bin carefully.

Clean the bin

Clean the clear bin with a damp cloth only.

Do not use detergents, polishes or air fresheners to clean the clear bin.

Do not put the clear bin in a dishwasher.

Clean the cyclone shroud

Clean the cyclone shroud with the brush on the combination tool to remove lint and dust.

Do not immerse the whole cyclone unit in water or pour water into the cyclones.

Refit the bin

Ensure the clear bin is completely dry before replacing.

To replace the clear bin, push the clear bin up and in to the main body of the appliance. It will click into place.

Close the clear bin base so it clicks into place and is secure.

Has cleaning the bin and cyclone resolved the problem?

Does the machine have power?

Clear the mini motorised head

With it removed from the machine, remove the Brush bar from the Mini motorised head.

Using scissors carefully cut any hair or fibres away from the Brush bar.

Reassemble the tool and attach it to the machine.

Test the tool without putting it in contact with any surface.

Does the Brush bar still not work properly without any contact?

Charge the machine

Charge the machine for 30 seconds.

Does the machine have power after 30 seconds on charge?

Charge the machine fully

Plug the machine in and leave it to charge for 3.5 hours before calling back.

Is there anything else we can help you with?

Which part do you need help fitting?

Fit the bin

Open the bin base.

Locate lug at the front of the cyclone and the recess inside the top of the bin, in line with the release catch for the tools.

Push the lug end of cyclone in first at an angle and then push the bin in towards the Main body until it clicks.

Close the bin base.

Is there anything else we can help you with?

Please call us to resolve this problem.

It looks like the Clear bin isn't working. We know how to fix it – we just can’t do it online.

One of our Dyson experts can help you get the parts or assistance you need.

Clear bin

Part no. 965660-03

Replacement clear bin for your Dyson vacuum cleaner.

€24.99

Clear bin

Clear bin

Part no. 965660-03

Replacement clear bin for your Dyson vacuum cleaner.

€24.99

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Please call us to resolve this problem.

It looks like the Cyclone isn't working. We know how to fix it – we just can’t do it online.

One of our Dyson experts can help you get the parts or assistance you need.

Cyclone

Part no. 965878-10

Replacement cyclone for your Dyson vacuum cleaner.

€64.99

Cyclone

Cyclone

Part no. 965878-10

Replacement cyclone for your Dyson vacuum cleaner.

€64.99

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Separator tool

Please note that separation of the cyclone and Main body can only done with the separator tool. The separator tool is included when ordering a replacement cyclone or Main body.

Remove the cyclone

Push the separator tool up in the crevice between the cyclone and mainbody.

While the separator tool is pushed up into the crevice, pull the cyclone away from the Main body until it is fully removed.

Fit the cyclone

Line up the Main body and cyclone.

Push the cyclone and Main body together firmly until they click in place.

If necessary, place the fitting tool onto the Main body so that the retaining ring is compressed before fitting the Main body and cyclone together.

Is there anything else we can help you with?

Apologies. We can’t help you online.

But our Customer Support Team will be able to solve your problem.

Call us on 01-475-7109

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent